ttl接线就是rx和tx和gnd，然后速率是125300 其他所有默认，有勾取的勾取消
默认可以直接引导，当然有说按任意键停止自动启动。
如果不自动启动默认虽然有22端口，但是由于root木有密码，所以是无法登录ssh的
所以要vi shadow文件复制一个root的密码进去保存，重新启动ssh服务即可用winscp和putty管理。。
备份系统
注意默认有uboot，，和现在的进入breed方法一直，但是，这个uboot的只认一个网卡，就是靠近电池那边的第一个网卡
root@OpenWrt:/etc/init.d# cat /proc/mtd
dev: size erasesize name
mtd0: 00060000 00020000 "u-boot"
mtd1: 00020000 00020000 "env"
mtd2: 01e80000 00020000 "fs"
mtd3: 00100000 00020000 "conf"
root@OpenWrt:/etc/init.d# dd if=/dev/mtd0 of=/tmp/uboot.bin
768+0 records in
768+0 records out
root@OpenWrt:/etc/init.d# dd if=/dev/mtd1 of=/tmp/env.bin
256+0 records in
256+0 records out
root@OpenWrt:/etc/init.d# dd if=/dev/mtd2 of=/tmp/fs.bin
62464+0 records in
62464+0 records out
root@OpenWrt:/etc/init.d# dd if=/dev/mtd3 of=/tmp/conf.bin
2048+0 records in
2048+0 records out
root@OpenWrt:/etc/init.d#
可以用ssh把备份的系统给拷贝出去咯。。。
DDR Training.............................................................Done
U-Boot 1.1.6 (Jun 6 2013 - 21:15:57) Mindspeed $Name: uboot_7_00_5 $HTTP Upgrade Server(192.168.1.1) $
DRAM: 512 MB
Comcerto Flash Subsystem Initialization
Flash: 32 MB
In: serial
Out: serial
Err: serial
Reserve MSP memory
DDR Training :
DLL_ADJ(0,1,2,3): 0x25,0x1d,0x20,0x20
WR_DQS:delay0 0x0, delay1 0x97, delay2 0x0, delay3 0x0
Net: Initiate AR8328 Switch, device=comcerto_gemac0.
Wait for AR8328 Reset.Done
comcerto_gemac0, comcerto_gemac1
GPIO1: 2
Hit any key to stop autoboot: 0
### JFFS2 loading '/boot/uImage' to 0x81000000
Scanning JFFS2 FS for uImage: ...uImage Found
...uImage Read Done
Loading kernel to address 0x81000000
### JFFS2 load complete: 1 bytes loaded to 0x81000000
## Booting image at 81000000 ...
Image Name: Linux-2.6.32.27
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1075316 Bytes = 1 MB
Load Address: 80808000
Entry Point: 80808000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.27 (root@darkstar) (gcc version 4.4.3 (GCC) ) #13 Thu Sep 19 05:02:33 CST 2013
CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387d
CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
Machine: Comcerto 1000 (Multifunction EVM)
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128016
Kernel command line: init=/etc/preinit root=/dev/mtdblock2 rw rootfstype=jffs2 console=ttyS0,115200 hwaddress=eth0,00:11:F7:A6:33:C0 mtdparts=comcertoflash.0:384k(u-boot),128k(env),31232k(fs),1024k(conf) partno=M83263G fppmode=1
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
allocated 2580480 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 504MB = 504MB total
Memory: 505728KB available (2620K code, 232K data, 104K init, 0K highmem)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:80
Calibrating delay loop... 648.80 BogoMIPS (lpj=3244032)
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
SPI core: loaded version 0.2
INFO: RCU detected CPU 0 stall (t=1000 jiffies)
have wated for LTSSM :8 ms
have wated for VC0 :25 ms
PCIe1: no device detected on link (3)
have wated for LTSSM :1000 ms
pcie_setup(0)
pcie_scan_bus(0)
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
pcie_setup(1)
pcie_scan_bus(1)
PCI: bus1: Fast back to back transfers enabled
slot 0, pin 1, irq 68
bio: create slab <bio-0> at 0
Switching to clocksource timer3
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Mindspeed gpio driver initialized
SPI core: add adapter comcerto-spi
arm1: Module loaded.
membuf_init: created membuf device(253, 0)
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
msgmni has been set to 988
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
console [ttyS0] enabled
loop: module loaded
nbd: registered device at major 43
comcertoflash.0: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x00000001
CFI id 0x00002201
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
comcertoflash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
4 cmdlinepart partitions found on MTD device comcertoflash.0
Creating 4 MTD partitions on "comcertoflash.0":
0x000000000000-0x000000060000 : "u-boot"
0x000000060000-0x000000080000 : "env"
0x000000080000-0x000001f00000 : "fs"
0x000001f00000-0x000002000000 : "conf"
c1k_eth_probe: gemac 0
eth0: C1000 Ethernet Controller 00:11:f7:a6:33:c0
c1k_eth_probe: gemac 1
eth2: C1000 Ethernet Controller 00:2a:2b:2c:2d:2e
Comcerto MDIO Bus: probed
Comcerto MDIO Bus: probed
i2c /dev entries driver
comcerto_wdt: support registered
cpuidle: using governor ladder
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing NETLINK_KEY socket
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (jffs2 filesystem) on device 31:2.
Freeing init memory: 104K
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -
Please press Enter to activate this console. NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
c1k_eth_open: eth0
Disabling GEM0 delay
c1k_eth_open: eth2
Disabling GEM1 delay
device eth2 entered promiscuous mode
br-lan: port 1(eth2) entering forwarding state
[PF_RING] Welcome to PF_RING 5.4.7 ($Revision: exported$)
(C) 2004-12 L.Deri <deri@ntop.org>
size1 =392 size2=172
size3=156[PF_RING] registered /proc/net/pf_ring/
NET: Registered protocol family 27
[PF_RING] Min # ring slots 4096
[PF_RING] Slot version 14
[PF_RING] Capture TX Yes [RX+TX]
[PF_RING] Transparent Mode 0
[PF_RING] IP Defragment No
[PF_RING] Initialized correctly
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Backport generated by backports.git backports-20130617-4-ge3220f5
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
lib80211: common routines for IEEE802.11 drivers
PCI: enabling device 0000:00:00.0 (0140 -> 0142)
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR5418 MAC/BB Rev:2 AR5133 RF Rev:81 mem=0xe02e0000, irq=68
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
tdi_reset: set Streaming disable mode
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: comcerto EHCI
comcerto-ehci comcerto-ehci.1: new USB bus registered, assigned bus number 1
comcerto-ehci comcerto-ehci.1: irq 5, io mem 0x0f000000
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: comcerto EHCI
usb usb1: Manufacturer: Linux 2.6.32.27 ehci_hcd
usb usb1: SerialNumber: comcerto-ehci.1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (7909 buckets, 31636 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
usb 1-1: new high speed USB device using comcerto-ehci and address 2
usb 1-1: New USB device found, idVendor=0424, idProduct=2514
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
xt_time: kernel timezone is -0000
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
ip_set version 4 loaded
xt_RAWNAT: Unknown symbol ipv6_find_hdr
Netfilter messages via NETLINK v0.30.
arp_tables: (C) 2002 David S. Miller
Ebtables v2.0 registered
ctnetlink v0.93: registering with nfnetlink.
SSDK Init OK!
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
fuse init (API version 7.13)
cfg80211: Calling CRDA for country: CN
cfg80211: Regulatory domain changed to country: CN
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
ADDRCONF(NETDEV_UP): wlan0: link is not ready
br-lan: port 2(wlan0) entering forwarding state
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
comcerto_fpp_module_init
comcerto_fpp_probe
fpp fpp: firmware: requesting fpp.axf
FPP is running $Version: fpp_7_00_5 $
i2c i2c-0: The new_device interface is still experimental and may change in a near future
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
i2c i2c-0: new_device: Instantiated device pcf8563 at 0x51
rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
rtc-pcf8563 0-0051: retrieved date/time is not valid.
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ath: phy0: TX while HW is in FULL_SLEEP mode
br-lan: port 2(wlan0) entering forwarding state
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
c1k_set_fast_path_enable 1
eth0: c1k_eth_close
c1k_eth_open: eth0
Disabling GEM0 delay
c1k_set_fast_path_enable 1
eth2: c1k_eth_close
c1k_eth_open: eth2
Disabling GEM1 delay
c1k_show_fast_path_enable
comcerto_cap_init
comcerto_cap_driver_init: start
comcerto_cap_register_capdev:
comcerto_cap_register_capdev:
cap_lan: comcerto_cap_open
device cap_lan entered promiscuous mode
device cap_lan left promiscuous mode
device cap_lan entered promiscuous mode
warning: process `nsdpf' used the deprecated sysctl system call with 1.42.
warning: process `nsdpf' used the deprecated sysctl system call with 1.35.
warning: process `nsdpf' used the deprecated sysctl system call with 1.36.
warning: process `parse_post' used the deprecated sysctl system call with 1.42.
warning: process `parse_post' used the deprecated sysctl system call with 1.35
保存到桌面
加入收藏
设为首页
工信部备案：湘ICP备14010293号-1
